see at the top line..
must be out for a few days now..
http://www.moodeaudio.org Forum:-> Link
(little installation reminder debian-stretch-lite: user pi pass raspberry..for ssh enabling ->sudo raspi-config)
for the european „Sabre-Lover“ ;-), Audiophonics.fr has now also our ES9038Q2M „on sale“(50€)..(LINK)
seems its almost identical with our „green-boards“ here;
they have also +15V DC plug on it, so i guess its PCB 1.04 minimum/upwards..
(User „Zek“ (thx a lot!) here from the forum means:“..This board has an additional regulator for a 5V pin and an additional capacitor (in the middle).“(see comments).
by that, Audiophonics has also a toroidal transformer „Transformer Toric 30VA 2x15V“ (LINK) on sale for only 17,90€ which seems to be ideal for our ES9038Q2M-boards..
(and a wonderful „wiring/installation“-tutorial/pictures for these torodial-transformer->http://forum.audiophonics.fr/viewtopic.php?t=389)
check it out 😉
because everyone visiting this site is really „on“ new infos to the ES9038Q2M here are some pics and a description of the new „V1.06“-pcb-layout, i would call it the „Green V1.06„..($39$ Ebay/49$-41€ Aliexpress)
they assembled also a DC-plug (here +15V DC) to it.. (to use it you have to short/solder J6 (is left above the plug from this view))
but the default voltage stays at DC +15V 0 -15V and u can still connect it directly to the board->“* It is recommended to use dual DC+-15V power supply to play board best results„
(maybe some other user can us tell the other differences in future)..
looks very nice 😉
today, after 60 !! days, my LCD1602+I2C-modul finally arrived..(2.00$ Aliexpress->LINK)
i have already a 2.6″ TFT-LCD display (320×240), but also want to check these 1602-LCDs (its „standard“ for the „real“-Arduino-User 😉 )
okay, there is not soo much to tell, except that i havent bring it to work in „full mode“ so far because (and thats why i write this article here too) it was the „hell again“ 😉 soldering the I2C-modul (in this case i took a 16pin pin-strip) on the LCD-PCB..
so if u can find a 1602-LCD with a I2C-modul already soldered on it, take it ;-)..
i extended my Bluetooth-IR-sketch now with a „blink“ from the whole display (“ lcd.backlight(); delay(250); lcd.noBacklight(); delay(250);“ 😉 everytime i make a command, type a „value“ via the Bluetooth-App; as confirmation..
Its blue and i first thought i print the source („CD,DVD,XMOS-USB etc..)“ on it; but there are no characters on it by now cause i guess i have to solder some pins again ;-(..
useful sketches i´ve found so far were:“identify the I2C-adress from the modul („i2c_adress.ino“) and a simple sketch to get data via the serial monitor and print it on the screen..(.inos and links here->http://essabre-90xx-rpi.sfb2.com/forum/showthread.php?tid=19 )
so far so good, many greets from here 😉
after i´ve got my „Arduino Mega 2560 R3“->on sale 11,99€ Amazon->LINK a few days ago, i just wanted to revive my „Project 1“ Cambridge Audio Azur A540 Remote via a „Bluepill“ (STM32F103C8T6) or an Arduino; original post here-> http://essabre-90xx-rpi.sfb2.com/2017/12/programming-subkurs-i-ir-receiver-raspberry-pi-project-1-cambridge-audio-azur-540a-remote/..
I´ve ordered an Arduino because this Bluepill/STM32-programming via the Arduino IDE is still very complicated at present imo, because there were nowhere really clear,simple instructions and libraries (pin assignments and so on)..(more maybe later)..
so i´ve decided to „fall back“ on this original Arduino-thing, hoped it would be easier at first for me..
long story short: (I´ve made a really long TuT over at the forum->http://essabre-90xx-rpi.sfb2.com/forum/showthread.php?tid=18)
because i didnt know how to send and receive IR-signals (simultaneously) and which pins i then i have to/use edit in the boarddefs.h (Arduino IRremote-library) i switched over to my HC-06 Bluetooth-Modul….
Full story (as said) here->http://essabre-90xx-rpi.sfb2.com/forum/showthread.php?tid=18
and now it works here absolute fantastic !!! 😉
came by chance over this !! :
(NEW: Aliexpress 39,99$/32,70€ incl.shipping->https://de.aliexpress.com/item/KGUSS-M7A-JRC55320-ES9038Q2M-I2S-DSD-Optical-Coaxial-Eingang-Decoder-DAC-Kopfh-rerausgang-Audio-verst-rkerplatine/32853239479.html
Voltage: DC 9-15V
PCB Measurements: 76 * 86MM
I2S-pins are reversed: GND, vakant, LRCK, BCLK, DATA
J1 short: coax-input
J2 short: opt (toslink)-input
J1 and J2 not short (open): I2S-input
J3, J4, J5, J6 not short (open), Filter = Apodizing Fast Roll-Off Filter
J3 nicht kurzgeschlossen:
J4 kurz, Filter = Ziegelwandfilter
J5 kurzgeschlossen, Filter = korrigierter minimaler Phasen-Schnell-Roll-Off-Filter
J6 kurzgeschlossen, Filter = Minimum-Phase-Slow-Roll-Off-Filter
J4 kurzgeschlossen, Filter = minimaler Phasen-Schnell-Abrollfilter
J5 kurzgeschlossen, Filter = linearer Phasen-Slow-Roll-Filter
J6 kurzgeschlossen, Filter = linearer Phasen-Fast-Roll-Off-Filter
VOL: 1-2 kurz zum Stummschalten, 2-3 kurz zur maximalen Lautstärke
Kann ein externes einzelnes Potentiometer sein, Drehgriff des Potentiometers zur Überbrückungsrichtung, gefolgt von der entsprechenden Verdrahtung und erhöht die Lautstärke von links nach rechts
(edit it to english later)..
and so, because i had great problems/was not possible to order from TaoBao direct, i got today a free 8$ coupon from yoybuy.com..checked it now for the first time and will then report here any info.. 😉
many thx to „Blackbear“ over at the Diyaudio.com-forum http://www.diyaudio.com/forums/digital-line-level/314935-es9038q2m-board-10.html
and because of min. 80% !! of the visitors here on the blog a searching for ES9038Q2M-related info, here are some results on his „research“:
In MoodeV4Beta on Dietpi he uses the „Audiophonics ES9028Q2M„-audio-settings..(for the ES9038Q2M)
„..Hello, in dietpi i had selected no driver = just left rpi-2835 (I left it without change after installation…), but in moode driver selection i choosed audiophonics 9028q2m, so it is strange that Moode takes control over dietpi driver (now I am thinking about it…) ? but it works, also tried to switch in dietpi config onto i-sabre-2km driver then restart and no sound so then i had to go into moode driver and to select audiophoincs 9028q2m, tehn reboot and it works again…strange..“
greets for now..
after listening for days through this super phenomenal Skysong-XMOS-USB-ES9018K2M-Combo (a really hifi-upgrade by 10-15%) i came back to my STM32F103-„Bluepill“/Arduino project to build your own DAC/display audio-parameter (Input,sample-frequency and so on)..
and i knew there was already such a project and it was !!!!
its the HiFi-Duino-TFT-Project on http://www.dimdim.gr/arduino/tft-hifiduino-code/ !!! (based on the famous/original HiFi-Duino-project/code; is well known)
and here->Universal USB to I2S Interface Indicator->http://www.dimdim.gr/arduino/universal-usb-to-i2s-interface-indicator/
after reading the documentation about it, our „F0,F1,F2,F3,DSD-on etc“-schematics became a really new sense->they were already used by this above mentioned code for example and also in conjunction with the Anamero-Combo-boards..look here->
the code looks like this->
// —————————- Amanero ——————————————————————————
* I1 = F0
* I2 = F1
* I3 = F2
* I4 = F3
* I5 = DSD_ON
* I6 = DSD 64 or 128
// Check for PCM or DSD
if (digitalRead(I5) == false) // PCM detected
type = 0;
if (digitalRead(I1) == false && digitalRead(I2) == false && digitalRead(I3) == false && digitalRead(I4) == false)
SR = 32;
else if (digitalRead(I1) == true && digitalRead(I2) == false && digitalRead(I3) == true && digitalRead(I4) == false)
SR = 176.4;
else if (digitalRead(I1) == true && digitalRead(I2) == true && digitalRead(I3) == true && digitalRead(I4) == false)
SR = 352.8;
else if (digitalRead(I1) == false && digitalRead(I2) == false && digitalRead(I3) == false && digitalRead(I4) == true)
SR = 384;
and so on !! burner 😉 ..
you can get the sketch here->Link or via the forum (http://essabre-90xx-rpi.sfb2.com/forum/); i will upload it there later too..
so to see, the absolute breakthrough i would say 😉
but this are only „teaser“; for me its absolute to complicated right now/at present and i don´t know if i continue to „walk on this way“/have the time for it in the near future but for introduction..
greets for now 😉